Asphalt Milling in the Lehigh Valley, PA
Based in Walnutport, PA (Northampton County). Serving Northampton, Lehigh, Carbon, and Monroe Counties. Owner Dale meets every customer on site and oversees each project from written proposal to final rolling.
Milling grinds off the worn top layer of asphalt so a new surface can be laid without raising the curb height, the garage apron, or the drainage grade. It is the precise way to refresh a pavement that has a solid base but a tired surface. DSP Paving mills and overlays asphalt across Northampton, Lehigh, Carbon, and Monroe Counties from Walnutport.
By removing just the top lift, milling keeps the existing grades and elevations intact. That matters at curb lines, drain boxes, and building entrances where adding material would create lips or trap water. The ground material is hauled and reused rather than wasted.
Milling costs less than full removal and puts less stress on the base because we are not digging into it. If your base is sound and only the surface has failed, milling and overlay is often the smartest path.
Get Your Paving Quote
Owner Dale meets every customer in person. No pressure, no obligations.
Signs You Need Asphalt Milling
Worn Top Layer
The surface is aged but the base beneath is still solid and stable.
Curb Height Matters
Adding material would raise the pavement above curbs, drains, or aprons.
Grade Needs Resetting
The pitch has drifted and water no longer flows off as it should.
Surface-Only Damage
Cracks and wear are in the top lift, not down in the base.
How We Do It
Inspect the Base
Dale confirms the base is sound so milling the top layer is the right call.
Mill the Top Lift
We grind off the worn surface to the depth needed to reset grade and profile.
Clean and Tack
The milled surface is cleaned and a tack coat bonds the new layer to the old.
Pave and Roll
Fresh hot-mix is laid and rolled flush to the existing curb and apron heights.
Mill & Overlay vs Full Removal
| Mill and Overlay | Full Removal | |
|---|---|---|
| When to use | Base solid, surface worn | Base soft or failed |
| Curb and grade | Stays the same | Rebuilt from scratch |
| Cost and stress | Lower, less base disturbance | Higher, full excavation |
Milling and overlay is a warm-weather, dry-surface job. The tack coat and hot-mix both need warmth to bond. In the Lehigh Valley, catch surface wear with a mill and overlay before freeze-thaw works it into the base.
Family-Owned, Three Generations In
Milling keeps your existing curb and apron heights instead of raising them.
We reuse the ground material rather than wasting it.
Owner Dale confirms the base is sound before recommending milling over full removal.
Serving Walnutport and the Lehigh Valley
What People Say
“DSP called half hour after I submitted my project. Was polite, and curious to my time frame. Had it done Fast and great looking.”
“Dale did my driveway, he did everything he said he would. I usually don't write reviews but this work was just superb.”
Asphalt Milling Questions
You May Also Need
Towns We Serve
Plain text for now. Town pages are coming soon.
Northampton County
- Walnutport
- Bethlehem
- Easton
- Northampton
- Nazareth
- Bath
- Bangor
- Hellertown
- Pen Argyl
- Wind Gap
Lehigh County
- Allentown
- Emmaus
- Macungie
- Trexlertown
- Coopersburg
- Catasauqua
- Whitehall
- Slatington
- Fogelsville
- Schnecksville
Carbon County
- Lehighton
- Jim Thorpe
- Palmerton
- Bowmanstown
- Lansford
- Weatherly
Monroe County
- Stroudsburg
- East Stroudsburg
- Tannersville
- Mount Pocono
- Brodheadsville
- Saylorsburg
Ready for a Driveway You're Proud Of?
Owner Dale meets every customer in person and stays in touch from quote to finish. Call now or send a quick request.